There are three basic types retaining walls. Sheet pile walls are made out of steel sheets. These
walls are not suitable for high pressure areas, but they can be used for applications up to six
meters tall. They can also made from precast concrete, or plastic. Retaining walls that are
mechanically stabilized can be used under bridges. They are made up of composite materials
and an alternate layer with soil reinforcement elements and compacted fill.
Sheet pile retainingwalls are ideal for small areas and soils. They have one-third of the wall
above ground level and two-thirds below. These retaining walls can be made from vinyl, steel or
wood, which is a difference to other types. They also cost less. They may have to be replaced
sooner. Regardless of the type of retaining wall you choose, it is important to thoroughly
consider the design and construction of the finished product to ensure a successful result.
Gravity retaining walls resist lateral pressure on the land behind them by opposing the weight of
the structure. In addition to gravity, these structures are subject to hydrostatic pressures caused
by water tables and passive soil pressure. A gravity retaining walls will not allow the structure to
tip over due to its weight. Gravity retaining walls are only a few metres in height and do not
contain anchors or embedded piles.
Anchored retaining walls are also available. Sheet pile retainingwalls are anchored in the rock or
dirt using cable strands. Anchored retaining walls are more expensive, but they are also a good
choice for many residential projects. They do not require much excavation and are quick and
convenient to install. However, the downside is that mortared walls are not ideal for retaining soil
pressures, and if you have a wet or sandy soil, it can be difficult to install.
There are three types of retaining wall. The most popular type of retaining wall is the anchored
earth wall. It uses a mixture of steel, wood, and plastic panels. The facing units are connected to
the rods or strips, and then anchored in the soil at their base. The strips or rods are then driven
into ground, and then expanded using mechanical means or pressurized cement. In addition to
these different types of retaining walls, they require a certain amount of space to be installed.
The segmental wall is another type. These are commonly used in patios and are available in a
variety of textures and colors. Concrete walls are another type of retaining Wall that is very
popular. Whether you choose to use concrete or other materials, you can rest assured that they
will look great. And as with any project, remember to consider the cost. There is no need for you
to go overboard. Concrete is still the most widely used material among home-owners despite its
The concrete retaining wall is one of the most common and economical types of retaining wall.
Concrete blocks are the most commonly used type, but you can also make them from stone.
Gravity retaining walls can be made from concrete segments, mortarless stone, or mortarless
brick. They often tilt backward into the soil. So, you must consider the height of your wall before
deciding on this type. It can add beauty to your property. A good choice for landscape design
and for boosting your property value.
Another type of retaining wall is the cantilever retaining walls. It is a wall that is attached to a
foundation slab. It holds a lot of soil. Because the cantilever-retaining wall rests on a slab
foundation it requires more careful engineering. The backfill is a weight that helps stabilize the
cantilever-retaining wall. It is more complicated than a traditional retaining wall and requires
more planning. When choosing a retaining walls, it is a good idea to consult a professional who
is familiar with structural engineering.
Another type of retaining walls is the gabion. These free-draining walls are often built in
locations that experience high levels of ground water. These areas are therefore important to
manage the groundwater. You can also plant vegetation in the gabion wall’s outer fascia cells. A
geocellular structure is an option when the slopes are gentle. Soil should be able drainage
around the wall. This will ensure that it doesn’t become too muddy and contaminated.
Gravity retaining wall are another option. They can be up to three meters tall and are designed
to resist soil pressure. For taller walls, however, you will need concrete footers and trenches in
order to support the weight. They are ideal for smaller spaces. There are several different
materials for crib retaining walls. Timber may be sufficient for smaller walls. For larger structures,
it is recommended to use stronger materials. There are a few types that can be used to build
retaining walls on steep slopes.